碾压混凝土抗裂性能的几个影响因素研究

影响碾压混凝土抗裂性能的因素很多，本文主要从水泥矿物成分、石粉含量、掺和料（氧化镁等）、骨料特性（弹性模量）及砂率等方面影响因素开展试验研究，分析各因素对碾压混凝土抗裂性能的影响效果。试验结果表明，砂率和石粉含量均存在碾压混凝土抗裂能力最大的最优含量；掺入适量的氧化镁掺和料和合理增加水泥熟料中的C，S和C4AF两种矿物成分含量，对提高碾压混凝土的抗裂能力非常有利；骨料的弹性模量是影响混凝土弹性模量的重要因素，使用低弹性模量骨料可以大大降低混凝土的弹性模量，增大极限拉伸值，提高混凝土的抗裂能力。     

简析Ⅲ类PHC管桩的成因及加固补强处理方法

本文主要通过Ⅲ类PHC管桩的形成分析,经过各方论证采用了合适的处理方法,取得了较好的效果。     

浅析露天栈桥改造

结合工程实例，论述了露天栈桥产生裂缝和腐蚀的原因，对栈桥结构进行了评价，提出了加固方案及加固施工中应注意的事项，经使用证明，加固效果良好。     

Threshold and growth mechanism of fatigue cracks under mode II and III loadings

ABSTRACT The fatigue crack growth behaviour of 0.47% carbon steel was studied under mode II and III loadings. Mode II fatigue crack growth tests were carried out using specially designed double cantilever (DC) type specimens in order to measure the mode II threshold stress intensity factor range, ΔK_IIth. The relationship ΔK_IIth > ΔK_Ith caused crack branching from mode II to I after a crack reached the mode II threshold. Torsion fatigue tests on circumferentially cracked specimens were carried out to study the mechanisms of both mode III crack growth and of the formation of the factory‐roof crack surface morphology. A change in microstructure occurred at a crack tip during crack growth in both mode II and mode III shear cracks. It is presumed that the crack growth mechanisms in mode II and in mode III are essentially the same. Detailed fractographic investigation showed that factory‐roofs were formed by crack branching into mode I. Crack branching started from small semi‐elliptical cracks nucleated by shear at the tip of the original circumferential crack.     

Damage mechanism in weldment of 2.25Cr-1Mo steel under creep-fatigue loading

The purpose of this study is to clarify damage process of “Type IV cracking” in weldment of a 2.25Cr-1Mo steel and to propose a micro damage prediction method. From continuous observation under a creep-fatigue test, it was found that spherical shape voids initiated and grew on grain boundaries in fine grain region and these voids grow continuously by changing their shape to crack-like. Both spherical and crack-like void growth rate equations were derived from the proposed void growth model. It was indicated that measured void growth rate under the creep-fatigue loading was well predicted by the growth rate equations.     

Aspects of rapid crack propagation in silicon

Fracture experiments with silicon specimens in recent years have shown the need for a new approach to the analysis of rapidly propagating cracks in single crystals. Behaviour and phenomena have been revealed that fracture in these materials is rather different from the fracture of both amorphous and polycrystalline materials. We show that continuum mechanics is insufficient for analyzing crack propagation in single crystals since it is unable to consider atomistic‐scale phenomena. Accordingly, we describe basic phenomena associated with rapid crack propagation in silicon : (i) anisotropic velocity‐dependent R‐curve behaviour, as a key phenomenon dictating atomistic scale behaviour, (ii) crack deflection from one cleavage plane to another as a mesoscopic scale phenomenon in single‐crystal fracture, (iii) the Rayleigh surface wave speed as the limiting crack tip velocity is re‐examined, (vi) the lowest crack velocity in brittle crystals is examined, and finally (v) the interaction between crack path and preferred cleavage planes in single crystals is depicted.     

Elastoplastic modelling of subsurface crack growth in rail/wheel contact problems

Propagation of small subsurface cracks subjected to shear under repeated rolling contact load is studied. An analytical crack model (Dugdale) with plastic strips at the two crack tips is employed. Compressive stresses promoting crack closure and friction between crack faces are considered. The triaxial stress state is used in the yield criterion. A damage criterion is suggested based on experimental LCF data. In a numerical study, critical crack lengths are found below which propagation of an existing crack should be effectively suppressed.     

Off-axis fatigue cracking behaviour in notched fibre metal laminates

The off‐axis fatigue cracking behaviour of notched fibre metal laminates under constant amplitude loading conditions was investigated experimentally and numerically. It was found that the off‐axis fatigue crack initiation life decreased as the off‐axis angles increased. This indicated that the off‐axis laminates raised the applied stress level in the aluminium (Al) layer and subsequently resulted in earlier cracking in the Al layer. The off‐axis fatigue crack initiation lives of notched fibre metal laminates were predicted using lamination theory and an energy‐based critical plane fatigue damage analysis from the literature. After a crack initiated in the Al layer, it was observed that the crack path angles of the off‐axis specimens were neither perpendicular to the fibre nor to the loading direction. A finite‐element model was established for predicting the crack path angles.     

Crack closure in fibre metal laminates

GLARE is a fibre metal laminate (FML) built up of alternating layers of S2-glass/FM94 prepreg and aluminium 2024-T3. The excellent fatigue behaviour of GLARE can be described with a recently published analytical prediction model. This model is based on linear elastic fracture mechanics and the assumption that a similar stress state in the aluminium layers of GLARE and monolithic aluminium result in the same crack growth behaviour. It therefore describes the crack growth with an effective stress intensity factor (SIF) range at the crack tip in the aluminium layers, including the effect of internal residual stress as result of curing and the stiffness differences between the individual layers. In that model, an empirical relation is used to calculate the effective SIF range, which had been determined without sufficiently investigating the effect of crack closure. This paper presents the research performed on crack closure in GLARE. It is assumed that crack closure in FMLs is determined by the actual stress cycles in the metal layers and that it can be described with the available relations for monolithic aluminium published in the literature. Fatigue crack growth experiments have been performed on GLARE specimens in which crack growth rates and crack opening stresses have been recorded. The prediction model incorporating the crack closure relation for aluminium 2024-T3 obtained from the literature has been validated with the test results. It is concluded that crack growth in GLARE can be correlated with the effective SIF range at the crack tip in the aluminium layers, if it is determined with the crack closure relation for aluminium 2024-T3 based on actual stresses in the aluminium layers.     

Express Method for Estimation of Tensile Strength and Crack Resistance of Brittle Media

The procedure is proposed for estimating the crack resistance and tensile strength of rocks by the results of experiments on disk samples with holes. The gradient approach to the strength problem is employed in processing the experimental data.